Difference between revisions of "Talk:Smooth Quake"
| Line 8: | Line 8: | ||
IPS panel with 240Hz minimum is recommended.<br> | IPS panel with 240Hz minimum is recommended.<br> | ||
TN has bad colors and viewing angles, VA has slow response time and Oled has higher input lag.<br> | TN has bad colors and viewing angles, VA has slow response time and Oled has higher input lag.<br> | ||
| − | The response time must stay inside de refresh cycle (1000/Hz) to avoid blur and take full advantage of the monitor's Hz.<br> | + | The pixels response time must stay inside de refresh cycle (1000/Hz) to avoid blur and take full advantage of the monitor's Hz.<br> |
[https://www.rtings.com/monitor/tests/motion/motion-blur-and-response-time Rtings has some reviews]. Order them by rise/fall time.<br> | [https://www.rtings.com/monitor/tests/motion/motion-blur-and-response-time Rtings has some reviews]. Order them by rise/fall time.<br> | ||
Some monitors have a fast enough response time but at the cost of ghosting. Take this into account.<br> | Some monitors have a fast enough response time but at the cost of ghosting. Take this into account.<br> | ||
| Line 36: | Line 36: | ||
- Control Panel > Power Options > High performance > Change plan settings > Change advanced settings > PCI Express > ASPM: disable<br> | - Control Panel > Power Options > High performance > Change plan settings > Change advanced settings > PCI Express > ASPM: disable<br> | ||
- Network Throttling: (I need to do a test on this)<br> | - Network Throttling: (I need to do a test on this)<br> | ||
| − | - [https://forums.guru3d.com/threads/windows-line-based-vs-message-signaled-based-interrupts-msi-tool.378044/ MSI | + | - [https://forums.guru3d.com/threads/windows-line-based-vs-message-signaled-based-interrupts-msi-tool.378044/ MSI Interrupt Mode Utility]: Change supported devices to MSI. A negative value means it's working. Do not enable devices if the supported modes field doesn't include Msi.<br> |
Interrupt priority should be undefined for all. Windows sets SATA to high and some ethernet drivers too. | Interrupt priority should be undefined for all. Windows sets SATA to high and some ethernet drivers too. | ||
* NVIDIA | * NVIDIA | ||
- NVCP: Create a new profile for ezquake and disable 'Threaded Optimization'<br> | - NVCP: Create a new profile for ezquake and disable 'Threaded Optimization'<br> | ||
| − | - [https://github.com/Orbmu2k/nvidiaProfileInspector/releases NvidiaProfileInspector]: Section 'Other' > | + | - [https://github.com/Orbmu2k/nvidiaProfileInspector/releases NvidiaProfileInspector]: Section 'Other' > Maximum Frames Allowed = 1 |
* AMD/ATI | * AMD/ATI | ||
| Line 48: | Line 48: | ||
'''EzQuake Launch'''<br> | '''EzQuake Launch'''<br> | ||
| − | To save energy you can change Windows power plan to high performance while playing and restore to balanced when finished.<br> | + | To save energy you can change Windows power plan to high performance while playing and restore to balanced when finished. Open cmdline and type powercfg -l to see their GUID. They should match the ones below.<br> |
Devices interrupts go to cpu0 by default. Excluding it for ezQuake will improve fps and stabilize frametime. [https://bitsum.com/tools/cpu-affinity-calculator/ Cpu affinity calculator] shows you what hexadecimal value you need to set in the cmdline after the /affinity (replace the word HexVal with the value you got from the calculator). | Devices interrupts go to cpu0 by default. Excluding it for ezQuake will improve fps and stabilize frametime. [https://bitsum.com/tools/cpu-affinity-calculator/ Cpu affinity calculator] shows you what hexadecimal value you need to set in the cmdline after the /affinity (replace the word HexVal with the value you got from the calculator). | ||
Open notepad and place these 3 lines (without the comment), change game path, and save as bat extension. | Open notepad and place these 3 lines (without the comment), change game path, and save as bat extension. | ||
Revision as of 06:57, 27 June 2023
Linux section is a mess. Someone clean it up?
WORK IN PROGRESS: JUNE 2023
Hardware
- Monitor
IPS panel with 240Hz minimum is recommended.
TN has bad colors and viewing angles, VA has slow response time and Oled has higher input lag.
The pixels response time must stay inside de refresh cycle (1000/Hz) to avoid blur and take full advantage of the monitor's Hz.
Rtings has some reviews. Order them by rise/fall time.
Some monitors have a fast enough response time but at the cost of ghosting. Take this into account.
Asus VG279QM is an excellent monitor. Aperture Grille's review.
- Mouse
Any modern mouse should be ok.
The sensor must not have smoothing, angle snapping and jitter.
1000Hz and DPI of 1600 minimum is recommended. Use only native DPI values to avoid interpolation.
Pixart 3389 sensor fills all these requirements.
Battle(non)sense DPI analysis.
Note: with 1000Hz+ mouse and keyboard you should use separate dedicated usb chips or a PCIe USB card.
- Keyboard
1000Hz minimum is recommended.
EVGA Z20 and Corsair K70 Rapidfire/Champion models are fast but expensive.
Configuration
- BIOS
Disable: Spread Spectrum ; Memory Scrambler (only works with ECC sticks)
Enable: Extreme Memory Profile (XMP)
- Windows
- Control Panel > Mouse > Pointer Options > Untick 'Enhance pointer precision' and leave pointer speed at 6th notch.
- Control Panel > Power Options > High performance > Change plan settings > Change advanced settings > PCI Express > ASPM: disable
- Network Throttling: (I need to do a test on this)
- MSI Interrupt Mode Utility: Change supported devices to MSI. A negative value means it's working. Do not enable devices if the supported modes field doesn't include Msi.
Interrupt priority should be undefined for all. Windows sets SATA to high and some ethernet drivers too.
- NVIDIA
- NVCP: Create a new profile for ezquake and disable 'Threaded Optimization'
- NvidiaProfileInspector: Section 'Other' > Maximum Frames Allowed = 1
- AMD/ATI
(someone write something)
EzQuake Launch
To save energy you can change Windows power plan to high performance while playing and restore to balanced when finished. Open cmdline and type powercfg -l to see their GUID. They should match the ones below.
Devices interrupts go to cpu0 by default. Excluding it for ezQuake will improve fps and stabilize frametime. Cpu affinity calculator shows you what hexadecimal value you need to set in the cmdline after the /affinity (replace the word HexVal with the value you got from the calculator).
Open notepad and place these 3 lines (without the comment), change game path, and save as bat extension.
powercfg -s 8c5e7fda-e8bf-4a96-9a85-a6e23a8c635c (high performance power profile)
start "" /wait /affinity HexVal "D:\QW\ezquake" -mem 1024
powercfg -s 381b4222-f694-41f0-9685-ff5bb260df2e (balanced power profile)
EzQuake Settings
in progress...
Issues: in progress...
- Network: lag spikes
- Network: packet loss
- Performance: unstable FPS